Pilot Light Repair • Cupertino
Water Heater Pilot Light Repair in Cupertino
Updated • By Joseph Castro, Owner • Licensed CSLB #1008381
A lot of Cupertino pilot-light calls start the same way: PG&E did gas line work nearby, and now the water heater won't relight — or it does, but a Bradford White ICON control panel is blinking a code nobody recognizes. Here's how to read what's happening and get the pilot staying lit again.
- Licensed CSLB #1008381
- Same-Day Service When Available
- ICON Control Diagnostics
- Trucks Stocked With Parts
- Upfront Diagnosis
- 4.8★ from 370 Google Reviews

What this service covers
Cupertino's pilot-light calls cluster around a few specific triggers. Here's what we see most.
- Air in the gas line after a PG&E service interruption or meter work nearby
- Bradford White ICON control lockout showing a blink code after restored gas service
- Worn thermocouple that no longer holds the gas valve open
- Failed thermopile on self-generating pilot systems
- Dirty or clogged pilot orifice from dust accumulation
- Flammable vapor sensor (FVIR) lockout on tanks in tight mechanical closets
- Failing gas control valve that won't hold a pilot signal
- Worn piezo or spark igniter producing a weak or no spark
- Low gas pressure following utility work in the area
Symptom → Likely Part
Match what you're seeing to the likely part before calling.
- Pilot won't catch at all after a gas service interruption → air in the line, may just need more purge time
- ICON control blinks the same code after reset → thermocouple or gas control valve
- Pilot lights but dies when the knob is released → thermocouple or thermopile
- No spark when pressing the igniter button → igniter
- Pilot holds but burner never fires → gas control valve
- Flame is weak, yellow, or flickering → dirty pilot tube or orifice
How to Safely Relight a Pilot (Once)
Attempt this only if you don't smell gas. If you do, stop and see the safety note below.
Find the rating label or ICON manual
Locate the relight steps on the tank, or the reset sequence in the Bradford White ICON control manual if your tank has one.
Set the control to Pilot
Turn the dial or control to Pilot mode and wait about five minutes, especially important after gas service was recently restored.
Hold, ignite, hold again
Press the control knob or igniter button, light the pilot, and hold for 30–60 seconds to let the thermocouple heat up fully.
Release and check the flame or display
The pilot should hold steady, and on an ICON tank, the status light should turn solid rather than blinking.
Note any repeating blink code
If the ICON control keeps blinking the same code after a reset, that points to a specific failed part — write down the pattern and call us rather than repeating the reset.
Parts on our trucks
- Universal and OEM thermocouples
- Thermopiles for self-generating pilot systems
- Complete pilot assemblies with FVIR sensor units
- Piezo and spark igniters
- Honeywell / Resideo gas control valves
- Robertshaw gas control valves
- Bradford White ICON system controls
Pilot Light Calls Across Cupertino
Cupertino sees a steady stream of utility and infrastructure work, and every gas service interruption near Monta Vista or Rancho Rinconada tends to generate a wave of pilot-light calls a day or two later. Many homes here also have Bradford White tanks with ICON electronic gas controls, which communicate faults through blink codes that most homeowners haven't seen before.
- Monta Vista (95014): pilots out after nearby PG&E gas line work
- Rancho Rinconada: Bradford White ICON control blink codes after power or gas interruptions
- Seven Springs: older tanks with worn thermocouples needing replacement
- Linda Vista: hillside homes where gas pressure fluctuations affect pilot stability
- Homes near De Anza College with shared utility infrastructure experiencing simultaneous outages
If the ICON control keeps faulting after a reset, it may point to the valve itself — see our gas valve replacement Cupertino page, or check water heater not heating Cupertino if the burner still won't fire.
City Overview • Santa Clara County
Water Heater Pilot Light Repair in Cupertino, CA — At a Glance
Cupertino is a mix of hillside custom homes, Eichler post-and-beam builds in Rancho Rinconada, and mid-century Monta Vista ranches. Eichler installs demand careful venting because there's no attic; hillside Inspiration Heights garages need custom drain-pan routing and CPC 507.2 seismic strapping tuned for raised foundations.
Permits pulled with
Cupertino Building Division
Utility
PG&E gas & electric
Local climate
Warm inland — western hillsides slightly cooler; low freeze risk
Housing stock we work on
Monta Vista mid-century • Rancho Rinconada Eichlers • Garden Gate ranch • Seven Springs custom
ZIP codes covered
- 95014
- 95015
Nearby landmarks
Apple Park • Stevens Creek Reservoir • Vallco/Main Street
Cupertino — Frequently Asked Questions
Which Cupertino ZIP codes do you cover?
Cupertino's primary ZIP is 95014, covering Monta Vista, Rancho Rinconada, Garden Gate, Seven Springs, Inspiration Heights, and the Stevens Creek corridor. We also cover the 95015 PO-box ZIP for scheduling purposes.
Do Cupertino water heater installs require a permit?
Yes. The City of Cupertino Building Division requires a plumbing permit for water heater installation and replacement. Cupertino inspectors verify CPC 507.2 seismic strapping, expansion tank on closed systems, T&P discharge routing, and combustion air/venting clearances.
Do you work on Monta Vista hillside garage installs?
Yes. Monta Vista and Inspiration Heights hillside garages often need custom venting runs, drain-pan routing to daylight, and seismic strapping upgraded for slab-on-grade to raised-foundation transitions. We scope these by site visit or photos before quoting.
How does Cupertino electric service affect heat-pump installs?
Cupertino is served by PG&E for both gas and electric. Heat-pump water heaters typically need a dedicated 30A/240V circuit — our in-house licensed electrician sizes the panel, pulls the electrical permit if needed, and coordinates the swap with the plumbing install.
Thermocouple vs Thermopile vs Gas Valve
Typical symptom
Thermocouple/thermopile fix: Pilot lights, dies when knob released
Gas control valve replacement: ICON blink code repeats after reset
Trigger
Thermocouple/thermopile fix: Normal wear over years
Gas control valve replacement: Often follows a gas service interruption
Cost tier
Thermocouple/thermopile fix: Lower-cost, quick swap
Gas control valve replacement: Higher-cost, more involved on ICON tanks
How we confirm it
Thermocouple/thermopile fix: Millivolt test at the pilot
Gas control valve replacement: Valve fails despite good millivolt reading, or ICON diagnostic confirms valve fault
Brands We Service for Pilot Repairs in Cupertino
Bradford White (including ICON electronic gas control systems), Rheem, A. O. Smith, and State. For a broader look, see water heater repair Cupertino.
Smell gas near the water heater? Leave first, then call.
Don't relight anything if you smell gas, even right after utility work. Leave the house, call PG&E's gas emergency line at 1-800-743-5000 or 911, and once it's safe, call us at (669) 337-9311.
Service hub
Broader water heater pilot light repair coverage in Cupertino.
Closest city pages
Nearest city hubs by drive time from Cupertino.
Frequently asked questions
Pilot Out After Gas Work in Cupertino?
Call (669) 337-9311 or text a photo of your water heater's rating label — and the ICON blink pattern if you have one — to (408) 470-0191.
- Licensed CSLB #1008381
- Bonded & Insured
- Open 24/7
Navien Service Specialist · Rinnai PRO · Noritz Certified
